Gun enthusiasts want the best when it comes to protecting their firearms and customized finishes. Especially when those finishes include ferrous metals, wood, stainless steel, synthetics, and alloys. There is no heating or baking required. Here are a few tips on using DuraCoat Aerosol, and be sure to ask your Lawrence, KS supplier about Peel 'N Spray templates.
Advancements in science offer new possibilities every day and now people have choices of textures for customizing their guns. From several selections of camo to attractive pearl finishes help protect the outside of all guns. All of these choices help personalize weapons for quick and easy identification.
One thing to remember is mixing this product with a hardener. It helps speed up drying time without reducing quality or appearance. Ratios of 12:1 is standard but for faster drying times slightly increase the amount of hardener. It also gives a higher gloss finish at about a 10:1 ratio. Read the directions on the product to make sure of the mixture.
When using templates that stick on the weapon, be sure to remove any residual adhesive materials before applying the product. A clean, dry rag and some mineral spirits will free up and remove the adhesive without damaging the project. Any residue left behind causes bubbles and other distortions that blemish the surface.
Typical drying time is overnight, but the process is accelerated by baking the item for 1 hour at 110 degrees F. At this point, it is safe to reassemble the weapon and test fire it. Once the weapon is thoroughly dry, most cleaners, lubricants, and abrasive solvents will have no adverse effect on the finish.
Keep in mind that DuraCoat is available in over 200 colors, including Clear and those 200 colors when mixed will match any color in the spectrum. The Aerosol Kit contains a spray can that easily allows mixing the dryer with the color mixture for perfect results and easy to access and clean up afterward.
The most important part of the whole process is to clean the weapon and all its parts. Dismantle it and place the parts in some order that help you remember how they go when putting the gun back together. DuraClean is excellent because it removes all grease, grime, dust, dirt and any other debris without even leaving a film.
As always, make sure the firearm is unloaded and completely dismantled for both safety and access to all areas of the surface, especially any tight corners or recessed areas where the human eye cannot see. Any coating product hardens after drying and presents a possible malfunction in discharging the weapon. Use a dental tool mirror if necessary to examine all internal areas.
Keep gun safety at the forefront of all activity involving a pistol, rifle or automatic weapon. After all, you could accidentally shoot yourself! The ask a well-trusted supplier about this new technology that allows people to customize their guns. Choose the colors and textures you like best and enjoy a new experience with a gun that reflects your personality.
Advancements in science offer new possibilities every day and now people have choices of textures for customizing their guns. From several selections of camo to attractive pearl finishes help protect the outside of all guns. All of these choices help personalize weapons for quick and easy identification.
One thing to remember is mixing this product with a hardener. It helps speed up drying time without reducing quality or appearance. Ratios of 12:1 is standard but for faster drying times slightly increase the amount of hardener. It also gives a higher gloss finish at about a 10:1 ratio. Read the directions on the product to make sure of the mixture.
When using templates that stick on the weapon, be sure to remove any residual adhesive materials before applying the product. A clean, dry rag and some mineral spirits will free up and remove the adhesive without damaging the project. Any residue left behind causes bubbles and other distortions that blemish the surface.
Typical drying time is overnight, but the process is accelerated by baking the item for 1 hour at 110 degrees F. At this point, it is safe to reassemble the weapon and test fire it. Once the weapon is thoroughly dry, most cleaners, lubricants, and abrasive solvents will have no adverse effect on the finish.
Keep in mind that DuraCoat is available in over 200 colors, including Clear and those 200 colors when mixed will match any color in the spectrum. The Aerosol Kit contains a spray can that easily allows mixing the dryer with the color mixture for perfect results and easy to access and clean up afterward.
The most important part of the whole process is to clean the weapon and all its parts. Dismantle it and place the parts in some order that help you remember how they go when putting the gun back together. DuraClean is excellent because it removes all grease, grime, dust, dirt and any other debris without even leaving a film.
As always, make sure the firearm is unloaded and completely dismantled for both safety and access to all areas of the surface, especially any tight corners or recessed areas where the human eye cannot see. Any coating product hardens after drying and presents a possible malfunction in discharging the weapon. Use a dental tool mirror if necessary to examine all internal areas.
Keep gun safety at the forefront of all activity involving a pistol, rifle or automatic weapon. After all, you could accidentally shoot yourself! The ask a well-trusted supplier about this new technology that allows people to customize their guns. Choose the colors and textures you like best and enjoy a new experience with a gun that reflects your personality.
About the Author:
Buy duracoat aerosol kit and many other accessories only on the Web. Check out this supplier's website now and select your favorite design at http://robinsonweaponry.com.
0 comments:
Post a Comment