A pool table is an elegant design used for indoor sports rooms and patios. The game of pool is played as a way of spending leisure time with friends and family. If the tables were to be made of materials that are durable, they can last around twenty years with less maintenance. The most vulnerable component of the structure is the felt. In consideration of pool table refelting Denver residents should know the procedure.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
The rails should be removed after that. This is done using a crescent wrench. Bolts attaching the rails are removed. Usually, the rails are also covered by the felt so they will need to be re-felted as well. The rails will then need to be carefully set on the floor close to its position in the table so that a mistake will not be made of attaching the rail to the wrong side.
The felt to be replaced is removed by using a staple remover to pull out staples at the edge of the felt. It will be essential to ensure that all felt is removed from the top of the table. The old one can be placed on a thrash bag from where it can be disposed of later.
The new felt should be placed carefully while making sure to inspect that there are no any damages or stains on it. It should then be cut using a sharp scissor while using the border of the table top as the guide. There needs to be some felt that is left over that will be used for re-felting the rails.
After making the cut, there is attachment of the felt to the table top using staplers. When stapling, you should start from the mid-point of one of the ends before proceeding to the left and right edges. Thereafter, you proceed to the opposite end and pull the felt tightly. This is followed by stapling it as was the case in the other side.
The side edges will then need to be stapled. You should ascertain that the staples are at an equal distance from each other and lined up in the correct way. For the pockets, 3 slits should be cut on every pocket before wrapping and stapling the felt on the edges of the pockets. The felt is tightly pulled prior to stapling.
The last step is to reassemble the structure. The rails are attached to their proper position using the crescent wrench. After insertion of the pocket lines, the re-felted table can be used.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
The rails should be removed after that. This is done using a crescent wrench. Bolts attaching the rails are removed. Usually, the rails are also covered by the felt so they will need to be re-felted as well. The rails will then need to be carefully set on the floor close to its position in the table so that a mistake will not be made of attaching the rail to the wrong side.
The felt to be replaced is removed by using a staple remover to pull out staples at the edge of the felt. It will be essential to ensure that all felt is removed from the top of the table. The old one can be placed on a thrash bag from where it can be disposed of later.
The new felt should be placed carefully while making sure to inspect that there are no any damages or stains on it. It should then be cut using a sharp scissor while using the border of the table top as the guide. There needs to be some felt that is left over that will be used for re-felting the rails.
After making the cut, there is attachment of the felt to the table top using staplers. When stapling, you should start from the mid-point of one of the ends before proceeding to the left and right edges. Thereafter, you proceed to the opposite end and pull the felt tightly. This is followed by stapling it as was the case in the other side.
The side edges will then need to be stapled. You should ascertain that the staples are at an equal distance from each other and lined up in the correct way. For the pockets, 3 slits should be cut on every pocket before wrapping and stapling the felt on the edges of the pockets. The felt is tightly pulled prior to stapling.
The last step is to reassemble the structure. The rails are attached to their proper position using the crescent wrench. After insertion of the pocket lines, the re-felted table can be used.
About the Author:
You can visit www.anytimebilliards.com for more helpful information about The Procedure Of Pool Table Refelting Denver.
0 comments:
Post a Comment